|
| |
Automatic gate operators
 |
 |
As you will see below the number of gate operators we use is limited.
The reason is that we have narrow down the best ones, after fifty years of
installing this equipment we have come to the conclusion that in this case
is not quantity but quality that counts.
-
We have the best
warranties in the industry.
-
We provide top notch
service.
-
Fast part replacement and
repair.
-
All of our operators are
ETL listed and class I, II, III and IV, UL 325
compliant.
-
Most of the operators
offer the option and convenience of a battery back up.
Door King 6002
Swing gate operator DK 9100
COMMERCIAL SLIDE GATE OPERATOR
DK 9200
INDUSTRIAL SLIDE GATE OPERATOR
CSW-200-UL High Traffic Commercial Swing Gate Operator
SL-3000-UL-1HP One Horsepower Slide Gate Operator
ALL-O-MATIC SW300
Swing gate operator
ALL-O-MATIC SL100
Sliding gate operator
Hercules Commercial Overhead Gate Operator
FAAC 400
Hydraulic swing gate operator
APPLICATIONS:
These actuators are designed to operate vehicular swing gates in residential, applications where side room is minimal. Actuators install directly on the swing gate eliminating the need for any mounting post or concrete mounting pads. Control panel is mounted separately from actuators.
ADVANCED FEATURES:
Self-adjusting, no maintenance limits.Plug-in loop detectors simplify installation.Gate TrackerŠ reporting output provides operator data to companion access controller (DoorKing 1803PC, 1815, 1817, 1818).Overlap feature for dual gate applications.
SPECIFICATIONS:
Operates vehicular swing gates up to 10 (601) and 13 (602) feet long .Designed with safety as the number 1 priority, these operators feature an electronic and mechanical inherent reverse system. DoorKing operators are known in the industry as being the safest vehicular gate operators available Manual keyed release.
APPLICATIONS:
The Model 9100 operator is designed to operate vehicular slide gates in residential and commercial applications. The 9100 is designed so that it can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. In addition, the operator can be pad or post mounted to meet any installation requirements.
ADVANCED FEATURES:
Self-adjusting, no maintenance limits. Partial-open feature. Anti-tailgating feature. Gate tracker reporting output. Ports for plug-in loop detectors. Two convenience outlets. Fail-safe release (fail-secure optional). Programming switches. Built-in reset switch. Built-in power On/Off switch.
SPECIFICATIONS:
Model 9100 Maximum gate length 30-feet. Maximum gate weight 1000 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.) 1/2 HP continuous-duty motor. 115 VAC, 5.4 Amps. APPLICATIONS:
Model 9200 operators are designed to operate vehicular slide gates in limited (Class III) and restricted (Class IV) applications only. These operators should never be used in applications serving the general public. These operators are designed so that they can easily be mounted in the front, center or rear of the gate without any costly and time consuming field modifications. Center mounting the operator requires an optional pedestal mounting base.
ADVANCED FEATURES:
Direct driven limit nuts. Partial-open feature. Anti-tailgating feature. Gate tracker reporting output. Ports for plug-in loop detectors. Two convenience outlets. Fail-secure operation, includes crank for manual operation. Programming switches. Built-in reset switch. Built-in power On/Off switch.
SPECIFICATIONS:
Model 9200: Maximum gate length 100-feet. Maximum gate weight 3000 pounds*. (*Assumes gate is on level ground, in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate Commercial Swing Gate operator for use in high traffic applications. The CSW-2000-UL is designed for high traffic applications such as heavily accessed gated communities and commercial buildings. It is capable of handling gates up to 600 lbs. and 18' at 75 cycles per hour with normal ambient temperatures. The most popular of all swing gate operating systems nationwide, it is designed with the "non-scissor action" arms that greatly reduce the risk of injury.
Heavy Duty, Slide Gate Operator that uses two 1/2 horsepower motors working together to equal one horsepower. For use on heavy gates The SL-3000-UL-1HP One of the most powerful slide gate operators. This operator was designed with heavy gates in mind. It delivers 210 pounds of pulling torque and is capable of 35 cycles per hour on gates up to 2000 pounds and 37 feet in length. Equipped with two 1/2 horsepower motors that motors and a heavy duty transmission. It is the perfect choice for large and heavy wrought iron gates
TL Approved Continuous Duty 1/2 H.P. Motor Newly Designed solid state circuit Board Phantom LoopStandard Feature Quite Operation Two fully adjustable erd's, allowing for separate adjustments on opening and closing the cycles. LED Readout shows status of operator Full system capability for access control system Full three year warranty on motor, gearbox and circuit board External terminal strip to mount (3) wire receiver
Easy adjustable limits switches Zinc gold plated frame Steel chassis Master slave capability standard feature built in Adjustable timer to automatically close gate - adjustable from 0 to 60 seconds Maximum operating time in any directions is 60 seconds Commercial operator at residential price
TL Approved Continuous Duty 1/2 H.P. Motor Newly Designed solid state circuit Board Phantom LoopStandard Feature Quite Operation Two fully adjustable erd's, allowing for separate adjustments on opening and closing the cycles. LED Readout shows status of operator Full system capability for access control system Full three year warranty on motor, gearbox and circuit board External terminal strip to mount (3) wire receiver
Easy adjustable limits switches Zinc gold plated frame Steel chassis Master slave capability standard feature built in Adjustable timer to automatically close gate - adjustable from 0 to 60 seconds Maximum operating time in any directions is 60 seconds Commercial operator at residential price Designed for 8' overhead gates, the smartest choice for low clearance high traffic underground parking garages.
Designed for parking garages, Hercules is carefully engineered to operate without vibration or noise, unlike any other overhead gate operator on the market. Designed with quality in mind, Hercules has features that most companies have not even considered including on their overhead operators. It is equipped with a 40 to 1 gear reducer/box that is lubricated by an oil bath and provides smooth and very quiet operation. To further ensure quiet operation, the Hercules is equipped with four heavy-duty noise isolators. The high quality instant reversing parking gate motor is capable of continuous operational cycles per day and has digital overload motor protection. Hercules has a key release and there are no exposed components, therefore greatly reducing the risk of injury. Since Hercules is only 8 inches thick, up to 10 inches thinner than other overhead operators, it is a better and safer choice for all The Model 400 heavy duty hydraulic swing gate operator is specifically designed for situations needing maximum versatility, such as apartment, subdivision, commercial/industrial and certain residential applications.
Features include:
Its power makes it ideal for large, ornate gates
Perfect for situations needing up to 125 degrees of swing
Models available with locks in the opened and/or closed positions
Operator is mounted inside the gate but still allows gate to open to the inside or outside
A convenient manual release is standard
The versatile FAAC control panel allows for six operating modes, including garage-door-like operation and a HOLD OPEN function
A battery back-up unit is available
Door King 6002
Swing gate operator
APPLICATIONS:
These actuators are designed to operate vehicular swing gates in residential, applications where side room is minimal. Actuators install directly on the swing gate eliminating the need for any mounting post or concrete mounting pads. Control panel is mounted separately from actuators.
ADVANCED FEATURES:
Self-adjusting, no maintenance limits.Plug-in loop detectors simplify installation.Gate TrackerŠ reporting output provides operator data to companion access controller (DoorKing 1803PC, 1815, 1817, 1818).Overlap feature for dual gate applications.
SPECIFICATIONS:
Operates vehicular swing gates up to 10 (601) and 13 (602) feet long .Designed with safety as the number 1 priority, these operators feature an electronic and mechanical inherent reverse system. DoorKing operators are known in the industry as being the safest vehicular gate operators available Manual keyed release.
Back to Electronics.
|
 |
 |
|
